How to use this page
The SmartR230 status page shows a short code next to each fault. Find that code below. The same code is kept in the event log on the device, so you can look it up later, after you have left the SmartR230 Wi-Fi.
Codes starting B are warnings the factory battery control module (BCM) reports, shown when SmartR230 is in BCM DIAGNOSTIC mode with the factory unit still fitted. Codes starting F are faults SmartR230 spots for itself from the car's battery voltage, key and engine signals.
The B codes are grouped the same way as on the SmartR230 status page, by what the car's dash shows: red warnings (a red battery symbol or red stop messages), white warnings (a white battery symbol, or load shedding the dash may not show at all) and other warnings. Where a code makes the dash show a message, that message is given under the code. A few codes the dash shows nothing for are listed at the end and are not reported for now.
These guides are a starting point. They do not replace a proper check of the car's batteries and charging system.
Page updated 24 October 2026. Matches SmartR230 firmware v107.15.
How the two-battery system works
The R230 has two batteries and a control module (the factory BCM) that looks after them. Knowing the basics makes the codes below easier to follow.
- Consumer (systems) battery. A 12 V 70 Ah sealed AGM battery in the boot, under the spare wheel cover. It runs almost everything in the car.
- Starter battery. A smaller standard 12 V 35 Ah battery at the back of the engine bay on the right. Normally it supplies only the starter motor, and it is the backup for the consumer battery.
- Normal running. A relay keeps the two batteries apart. With the engine running, the alternator charges the consumer battery and the BCM charges the starter battery, adjusting for temperature.
- Emergency mode. If the consumer battery is too weak when the key goes in (below about 10.8 V), the BCM joins the starter battery to it and switches off non-essential loads so the engine can start.
Working on the batteries
- Disconnecting: key out, all loads off. Disconnect the earth leads first, then the positive leads.
- Reconnecting: key out. Connect the starter battery first and the consumer battery last. The wrong order can set warnings or trigger emergency mode.
- After a flat spell or new batteries, check the windows, seats, steering wheel and mirrors, air conditioning, stability control and tyre pressure monitoring work normally. Any that do not may need to relearn.
- Charging: charge each battery directly across its own terminals. If the voltage is under about 7 V, a normal charger may not start.
- Jump starting: connect to the starter battery positive terminal and a good earth on the engine. Never jump from the consumer battery.
- Testing: the consumer battery is AGM, so old acid-density and load tests are not suitable. Use a tester made for AGM batteries.
Factory BCM warnings (B codes)
Red warnings
The dash shows a red battery symbol with Visit workshop (B02, B03, B04, B08), or red stop messages (B12).
B02Relay K57 defective
The factory BCM reports a fault with the cut-off relay K57. This warning does not always mean the relay is faulty. Before replacing anything, ask whether the batteries have recently been disconnected or replaced.
- Battery order. If both batteries were disconnected and then reconnected, the order matters. Starter battery first, then the consumer (systems) battery gives a healthy BCM. Consumer battery first, then the starter battery gives this warning.
- It stays until the car sleeps. Stopping the engine or switching the ignition off does not clear it. It cleared on our test bench once the BCM had gone through a full sleep and wake. Switch off, lock the car, and leave it until it has gone to sleep before waking it again.
- If it returns after the car has slept and woken again, the relay, its wiring or the supply to it should be checked by a specialist.
If the relay has really failed, the car can no longer use the starter battery as a backup.
We are still measuring how long the car needs to sleep for the warning to clear.
On the dash: a red battery symbol with Visit workshop. This is the same display as B02, B03, B04 and B08, so the dash alone does not tell them apart.
B03Starter battery fuse defective
The factory BCM has lost its connection to the starter battery. That is what it reports as a defective fuse, but a blown fuse is only one of the possible causes. Check in this order:
- Is there a starter battery fitted? It is in the engine bay.
- Is it connected? Check both terminals are tight and clean, and that no cable has been left off after other work.
- Check the fuse in the front fuse block, upper left of the passenger footwell. The starter battery supply is protected by a 100 A fuse there.
On the dash: a red battery symbol with Visit workshop. This is the same display as B02, B03, B04 and B08, so the dash alone does not tell them apart.
If all three are fine and the warning stays, have the car's wiring and the BCM checked by a specialist.
B04Key-inserted signal not recognised
The battery control module wakes when the key goes into the ignition. If it never sees that signal it cannot manage the batteries. Check:
- Remove the key and insert it again. If no start follows within about 30 seconds the module goes back to standby until the key is reinserted.
- Check the supply to the ignition switch and its fuses. There is an 80 A fuse in the front fuse block in the passenger footwell, and a small 7.5 A fuse in the boot, right side.
On the dash: a red battery symbol with Visit workshop. This is the same display as B02, B03, B04 and B08, so the dash alone does not tell them apart.
If the warning stays, have the ignition switch and its wiring checked by a specialist.
B08Supply battery state-of-health warning
The battery control module thinks the consumer battery is wearing out. It is a sealed AGM battery and cannot be judged by the old acid-density or load tests.
- Have it tested with a tester made for AGM batteries.
- Check its age. If it is old, replacement is the likely answer.
- After fitting a new one, reconnect in the right order and check the systems listed above for normal operation.
On the dash: a red battery symbol with Visit workshop. This is the same display as B02, B03, B04 and B08, so the dash alone does not tell them apart.
B12Red stop messages: Brake defective, then Battery/Alternator
The dash shows red stop messages: first Brake defective, then Battery/Alternator. We have seen the dash do this when the factory BCM reports this warning.
The cause is not yet identified. Detailed checks are being added.
White warnings
The dash shows a white battery symbol with Electrical consumers offline (B01, B13). Load shedding (B05, B06) limits comfort items to save power, and the dash may show no message for it.
B01Emergency operation: priority 1 and 2 loads off, starter battery supporting
The car's battery control module has found the consumer battery in the boot too weak to run the car, so it has joined the starter battery in the engine bay to help. To save power it switches off non-essential items such as:
- Seat heaters and seat fans
- Rear window heater
- Parking sensors
- Air conditioning blower (limited to half power)
- Radio volume (limited)
- The roof (it will only go up, not down)
This is the car protecting itself. It usually means the consumer battery is flat, worn out, or was recently disconnected. Check in this order:
- Charge the consumer battery with a proper charger, or run the engine. The restrictions normally lift after roughly 8 to 18 minutes of running, once the voltage has recovered.
- Test it. It is a sealed AGM battery, so the old acid-density and load tests are not suitable. Use a tester made for AGM batteries.
- Check the terminals on both batteries are clean and tight.
- Were the batteries recently disconnected? Follow the reconnect order above (starter battery first, consumer battery last).
On the dash: a white battery symbol with Electrical consumers offline. B13 shows the same.
If the consumer battery tests healthy and the warning keeps returning, have the charging system checked by a specialist.
B13Emergency operation: priority 1 or priority 2 loads off
The factory BCM has switched off either its priority 1 or its priority 2 loads. Detailed checks are being added.
On the dash: a white battery symbol with Electrical consumers offline. B01 shows the same.
B05Load shedding
The factory BCM is cutting back on comfort items to save power. In our tests on the car the climate control fan was limited and the roof would not operate. The BCM reports load shedding in stages: SmartR230 shows the lighter stages as B05 and the heaviest as B06.
On the dash: there may be no message at all, so the first sign can be a weak fan or a roof that will not move.
What sets it off and what to check are being added.
B06Load shedding, heaviest stage
The heaviest load-shedding stage. In our tests on the car the climate control fan ran very low, the rear window heater was switched off and the roof would not operate.
On the dash: there may be no message at all.
What sets it off and what to check are being added.
Other warnings
B09Unrecognised warning reported by the BCM
The factory BCM reported a warning that SmartR230 does not recognise yet. The code is kept in the event log on the device.
If you see it, please email info@smartr230.co.uk with what the dash showed at the time. It helps us work out what it means.
Codes not currently reported
The car's dash shows no message for the codes below, so SmartR230 does not report them for now. The codes are kept, so older links still land here, and they will be brought back if their meaning is confirmed.
- B07 – emergency operation, priority 1 and 2 loads off, second battery supporting. On its own the dash shows nothing. Sent together with other emergency warnings (as the car does in deeper emergency stages) it shows the same as B01 and B13.
- B10 – BCM reports itself not active.
- B11 – battery not being charged.
- B14 – engine start capability at risk.
SmartR230's own faults (F codes)
F01Battery voltage low with key out
The consumer battery voltage stayed low while the key was out.
- Charge and test the consumer battery. Use a tester made for AGM batteries.
- Check the terminals.
If it keeps going low after a full charge, the battery may be worn out.
F02Battery voltage low with key in
The battery voltage stayed low with the key in. The car's emergency mode begins below about 10.8 V at this point (see B01).
- Charge and test the consumer battery.
- Check the terminals on both batteries.
If it stays low after a full charge, the battery may be worn out.
F03Weak cranking
The voltage dropped further than expected while cranking. On this car the starter battery in the engine bay supplies the starter motor, and the consumer battery supplies everything else.
- Check the starter battery is fitted, charged and its terminals tight.
- Check the consumer battery.
If both batteries test well, have the starting circuit checked.
F04Not charging with engine running
The voltage stayed too low with the engine running, so the car does not seem to be charging. This is closely related to B11.
- Check the fuses in the front fuse block in the passenger footwell.
- Check the batteries are connected and the terminals tight.
If it stays low, have the alternator and charging system checked.
F05Car not going to sleep
After the car is parked, its modules should settle down and the car should go to sleep. SmartR230 raises F05 in either of two cases:
- Kept awake. The ignition switch has gone quiet but other modules stay busy for more than about 10 seconds: something is keeping the car from sleeping.
- Waking itself up. The car goes to sleep, then wakes again on its own, 3 times within 10 minutes, while parked and with nobody using it.
Wakes you cause yourself, with the key fob, the key, a door, the boot or the locking, are not counted. A wake-up warning clears once 10 minutes pass without the pattern repeating.
A car that will not sleep slowly drains its batteries, so it is worth finding the cause. On the one car where we have recorded the waking pattern, the central locking pump woke the car every 15 seconds or so.
Detailed checks are being added.