Overview
This guide is the written companion to our installation walkthrough video and covers fitting the SmartR230 emulator adjacent to the rear SAM. It assumes the original BCM has already been removed as part of your replacement, leaving a spare connector at the CAN bus strip that previously fed it.
The install uses a fuse-tap method for power, so you don't need to cut into any of the car's original wiring. Everything is reversible.
Where to put it
We recommend mounting the emulator inside the cubby space behind the seats, adjacent to the rear fuse block, so the LED is visible through the gap and the unit stays easy to reach if you ever need to unplug it. The case has mounting lugs, which are handy if you're fixing it to a flat panel - if you're tucking it into a tighter gap, you can trim the lugs off and use a strip of Velcro instead.
Before you start
Trim clips get brittle in cold weather, so this job is easier in mild conditions. Work carefully around the air lines and wiring loom near the rear SAM, and avoid yanking on connectors.
Tools Required
Part 1: Accessing the Rear SAM
Step 1 - Rear center console
- Remove the two T15 screws inside the rear center console.
- Lift the centre rear console section out.
Step 2 - Clear the way
- Slide the driver's seat fully forward.
- Lift the door/sill seal off - start from the back end, since the front has a hook that tucks under the carpet and can tear it if pulled from the wrong end.
Step 3 - Metal side panel removal
- Remove four T15 screws: two together, plus one further round the side.
- Pull the inner panel free and set it aside.
- Unclip the retaining clip that holds the next section down.
- Pop the trim piece out.
- Remove one T20 screw.
- Push the panel to release the remaining internal clips, then lift it up and out.
Step 4 - Loosen the rear SAM housing
- Using the 4mm Allen key, loosen (not fully remove) the bolts holding the compartment - just enough that the unit can move.
- Remove the housing screws (T20 and T15) and lift the housing to access the connectors underneath.
- The unit lifts up and slides out of two slots at the back. Take your time here - there's an air line loom attached, so don't pull hard.
Step 5 - You're at the rear SAM
With that trim out, you have everything you need to install the emulator. For reference, the fuse module sits on top, the CAN gateway is adjacent to the main body of the unit, the roof module is underneath, and there are a couple of sensors mounted nearby.
Part 2: Wiring the Emulator
The emulator has three connections: earth, permanent 12V, and the two CAN bus wires into a single dual DuPont connector.
Earth
Connect the emulator's black earth wire to a solid earth point using the 10mm socket/spanner. This point is located just inside the door, now exposed since the trim has been removed.
12V permanent live
- Identify the permanent-live feed running from the rear SAM's fuse box (thick red/green wire from the purple fuse block).
- Fit the supplied fuse tap into that fuse position - this taps the circuit without altering the car's original wiring.
- The emulator has its own internal fuse (500mA, supplied fitted) - you don't need to add separate fusing beyond the tap itself.
Once earth and 12V are both connected, the emulator's LED will light solid red - powered up and waiting for a CAN signal.
CAN High / CAN Low
- Find the spare connector strip that used to feed the original BCM - it should already be disconnected with nothing on the end of it.
- The two wires you need are colour-coded red (top) and brown (bottom) at every position along that strip - red is CAN High, brown is CAN Low. Brown is not an earth - treat both as signal wires.
- Use the DuPont pin connector on the emulator's CAN leads to plug straight into that strip; any position on the strip is fine.
- Important: red to red (top), black/brown to brown (bottom). Push firmly.
Once connected, the LED changes from solid to flashing - this means the CAN bus is active and the emulator is receiving traffic. If it doesn't, the car may be asleep; try waking it by opening and closing a door. If the emulator is connected correctly, the light will flash.
Part 3: Testing
- Insert the key and start the engine.
- Confirm there's no battery/BCM fault warning on the dash.
- With the key out, watch the LED: it should keep flashing for circa 20 seconds, then go steady - this is an indication the car has gone to sleep.
Part 4: Reassembly
Reverse of Part 1
- Refit the SAM housing and tighten the Allen bolts just enough to hold it - no need to overtighten.
- Refit the housing screws (T20/T15).
- Refit the side panel: line up the locating holes, seat it firmly, then refit its screws (T20).
- Watch for the small retaining clip that holds this trim section on - it's commonly damaged or missed. Make sure it's engaged before moving on.
- Refit the sill/door seal. There's a small tab on the underside that needs to locate into the edge of the carpet - if that tab or its clips have gone soft with age, a strip of tape behind them can restore enough grip to hold it firmly in place.
- Refit the rear center console and its two T15 screws.
Questions?
If anything in this guide isn't clear, get in touch and we'll help you through it.
info@smartr230.co.uk